福妙康


Fumiaokang
首页
联系我们
新闻资讯
产品中心
关于我们
在线留言

福妙康


产品中心
首页
在线留言
新闻资讯
关于我们
联系我们
Fumiaokang

NEWS

新闻资讯

Debugging method of one-off Respirator: all-round analytic debugging problem
来源: | 作者:广东福妙康医疗科技有限公司 | 发布时间: 306天前 | 186 次浏览 | 分享到:

The disposable mask machine is also called the disposable mask manufacture machine, which is composed of the mask body machine, the inner ear belt mask machine, the outer ear belt mask machine and the belt type mask machine.

一次性口罩机又叫一次性口罩制造机,它由口罩本体机、内耳带口罩机、外耳带口罩机、绑带式口罩机组成三条生产不同一次性口罩的口罩生产线。

Disposable face mask is the most common mask in our lives, disposable face mask machine manufacturers are also the most, then we understand the debugging of disposable face mask machine how much? The following Kuaiyuda small series for you to explain in detail the one-time plane mask inner ear belt machine routine debugging.

一次性平面口罩是我们生活中最常见的一种口罩,一次性口罩机厂家也是最多的,那么大家对一次性口罩机的调试了解多少?下面快裕达小编为大家详细讲解一次性平面口罩内耳带机的常规调试。

1, open the start stop switch and the power switch, the power switch built-in light.

 2. Adjust the air pressure: the Air Pressure Valve is under the work table plate, open the door plate of the equipment can see the air pressure valve. Adjust the pressure according to the actual situation. When some bodies are out of sync, the pressure is increased. The working pressure is generally adjusted in the range of 0.2 ~ 0.6 MPA.

 一、打开开始停止开关与电源开关,电源开关内置灯亮。

      二、调整气压:气压阀在工作台板的下面,打开设备的门板就可以看到气压阀。根据实际情况调整压力。当有些机构动作不同步的时候就将压力调大些。工作气压一般在0.2~0.6MPa范围内调整。

3,Sound Wave Inspection Adjustment: (when the equipment is stopped)

(1) turn on the power switch of the ultrasonic generator and press the "sound check" switch. If the amplitude indicator rises sharply and exceeds 100, the frequency is too far from the resonance point, the "sound adjustment" knob must be adjusted. Visual amplitude display, left hand press the "sound check" switch (not more than 3 seconds) , right hand turn the "sound adjustment" Knob, amplitude display pointer to the lowest point. If the amplitude indicator indicator is not down but up during adjustment, turn the "Sonic Adjustment" knob in the opposite direction. The reading of the amplitude indicator is within 50, and that of the ammeter is below 0.6 a. After adjusting the sound wave, tighten the butterfly nut and close the protective cover.

 (2) no-load test, if the "overload indicator" is on, then there is something wrong with the equipment. At this time does not allow the start-up work, must shut down to check the reason, after removing the fault can start-up work.

三、音波检验调整:(设备处于停止运行时)

     (1)打开超声波发生器电源开关,按下“音波检验”开关,如振幅显示器指标急升并超过100,则表示频率距谐振点太远,须调整“音波调整”旋钮。目视振幅显示器,左手按下“音波检验”检查开关(勿超过3秒),右手旋转“音波调整”旋钮,将振幅显示器指针调到最低点。调整时如振幅显示器指标不是下降、而是上升,则反方向旋转“音波调整”旋钮。振幅显示器指标的读数在50以内,电流表指标的读数在0.6A以下是最佳工作状态。调整好音波后要把蝶形螺帽拧紧,并关好保护盖。

2)空载测试时,如“超载指示灯”亮,则表示设备有问题。此时不允许开机工作,须关机检查原因,排除故障后方可开机工作。

4. Cooling Fan Inspection: Check that the cooling fan is working properly to ensure that the Ultrasonic transducer can work for a long time.

  四、冷却风扇的检验:检查冷却风扇是否在正常工作,以确保超声波换能器在工作时能长时间工作。

5. CHECK THE PNEUMATIC COMPONENTS:

1) turn on the power, connect the air passage, and switch the manual automatic switch to manual gear.

(2) open the feed tray switch, check whether the feed tray can run fast and steadily and locate accurately. After the inspection, close the material tray switch .

(3) and open the mask clamp switch to check whether the mask clamp is in normal operation. Close the clamp switch after inspection.

(4) open the aggregate cylinder switch, check whether the aggregate cylinder normal action. Turn off the aggregate cylinder switch after inspection.

(5) open the sideband welding switch, see whether the sideband die can be normally pressed down.

(6) open the ear belt to turn the right switch, see if the right side of the rotary cylinder action and action in place.

(7) open the ear belt to turn the left switch, to see if the left side of the rotary cylinder action and action in place.

(8) open the ear band cut-off switch, check whether the ear band cut-off small cylinder is working and can reach the designated cut-off position.

(9) open the ear belt return material switch, check whether the ear belt return material small cylinder can work normally, and can make the ear belt clip piece loose.

(10) open the ear band fusion switch and check whether the ear band die can work and reach the designated position.

五、检查气动部件:

1)打开电源,接通气路,将手动自动切换开关切换到手动挡。

    (2)打开料盘开关,检查料盘是否能快速稳定的运行并定位准确。检查完后关闭料盘开关

    (3)打开口罩夹送夹具开关,检查口罩夹送夹具是否正常动作。检查完后关闭口罩夹送夹具开关。

4)打开集料气缸开关,检查集料气缸是否正常动作。检查完后关闭集料气缸开关。

    (5)打开边带熔接开关,看边带压模能否正常下压。

    (6)打开耳带回转右开关,看右边的旋转气缸是否动作且动作到位。

    (7)打开耳带回转左开关,看左边的旋转气缸是否动作且动作到位。

    (8)打开耳带剪断开关,检查耳带剪断小气缸是否工作且能到达指定的剪断位置。

    (9)打开耳带退料开关,检查耳带退料小气缸是否能正常工作,并能使耳带夹块松开。

   (10)打开耳带熔接开关,检查耳带压模能否工作并到达指定的位置。